Sep 21, 2023 Leave a message

How to build the checker brick of the regenerator wall of the hot blast stove

Products Description

 

Before laying the lattice bricks, the bottom of the furnace must be leveled by leveling the ring band under the grill and then leveling the lattice bricks when you start laying the bottom of the furnace.

 

Products Specifications

 

When laying the regenerator for the internal combustion hot air furnace, lay the vertical centerline from the thermocouple hole at the top of the furnace according to the sprayed centerline, place the centerline at the bottom of the furnace, and then mark the regenerator on the surface of the sprayed layer. The cross centerline extends as the height of the masonry rises.
How to build the checker brick of the regenerator wall of the hot blast stove

The layout of the regenerator for an external combustion hot air furnace is the same as for the internal combustion type. First, the cross centerline of the furnace is marked on the surface of the sprayed layer using the sprayed centerline as a reference and extending with the rise of the masonry height.
How to build the checker brick of the regenerator wall of the hot blast stove

When masonry regeneration furnace furnace wall, should check the verticality and curvature of the furnace wall and grate below the hole combination brick, to confirm whether it is in line with the design and construction requirements, hole combination brick masonry is completed shall not be closed....
How to build the checker brick of the regenerator wall of the hot blast stove

Spray the internal combustion type enclosure first, and then start masonry lattice bricks. When masonry, the multi-circle wall should be masonry from the inside to the outside, the inner circle of bricks first, the outer circle of bricks close to the inner circle of lattice bricks for masonry. The gap between the water-stopping bricks and the mortar layer should be solidified with asbestos board or filler, and the top surface of the filler should not be lower than the surface of the masonry by 500mm.
How to build the checker brick of the regenerator wall of the hot blast stove

When masonry external combustion hot air furnace enclosure, it should be masonry according to the center line. The enclosure structure composed of multiple rings is built from the outer ring brick layer to the inner ring brick layer, and the flatness of the inner radius of the brick layer should be confirmed during masonry. When the inner ring is built with brick masonry, the elevation of the brick layer should be marked on the heat-insulating refractory brick layer.
How to build the checker brick of the regenerator wall of the hot blast stove

Internal and external combustion hot air furnace shell upper and lower sections of masonry expansion joints and sliding joints should be reserved according to design requirements, the surface of each section of the supporting plate with refractory casting material leveling.
How to build the checker brick of the regenerator wall of the hot blast stove

Regenerator grid brick is generally seven-hole grid brick, masonry should be staggered in each layer, the upper and lower grid holes should be flush. Before masonry should be according to the design size of the enclosure edge location and connection of the grid brick pre-sorting and marking.
How to build the checker brick of the regenerator wall of the hot blast stove

Before lattice brick masonry, in the wall masonry 0 °, 90 °, 180 °, 270 ° four angles to pull out the cross center line, and then in the 90 °, 270 ° line on both sides of the two columns of masonry center. Line, the center line is listed as the center line of the first column of masonry.
How to build the checker brick of the regenerator wall of the hot blast stove

The first layer of lattice bricks is pre-laid using the dry placement method. After checking its center position accurately and qualified, formal masonry. After completing the masonry and confirming that the surface flatness of the masonry meets the requirements, start laying the second layer of lattice bricks....
How to build the checker brick of the regenerator wall of the hot blast stove

Expansion joints between lattice bricks should be 4mm for clay lattice bricks, 8mm for high alumina lattice bricks, and 12mm for siliceous lattice bricks. fill the expansion joints with yellow cardboard or foam boards, and stick the expansion joint boards on the side of lattice bricks, and paste them while laying.
How to build the checker brick of the regenerator wall of the hot blast stove

After the lattice brick masonry is completed, check the location of the lattice hole again to see if it is smooth, and use the checking tool to pass through the full height of the lattice hole, that is, the end of the construction.

How to build the checker brick of the regenerator wall of the hot blast stove

 

If you are interested refractory bricks, contact us now!

Email: info@zaferroalloy.com Whatsapp: 8615896822096

Send Inquiry

Home

Phone

E-mail

Inquiry