Jul 29, 2025 Leave a message

Ferro Silicon 45 vs Ferro Silicon 75: Composition, Duty and Selection Guide

What the Grade Numbers Actually Mean

In ferrosilicon trade, the number behind "FeSi" is the nominal silicon content of the alloy, not a purity guarantee of the finished heat. FeSi45 sits in the 40-47% Si band, while FeSi75 sits in the 74-80% Si band. Delivery requirements for these grades are normally written against the ferrosilicon grade table of GB/T 2272, which fixes silicon ranges together with caps on aluminium, carbon, sulphur and phosphorus for each grade; ISO 5445 describes the same class of technical delivery conditions for ferrosilicon. Because the two grades carry very different silicon levels, the residual iron content differs as well: FeSi45 contains roughly half iron by mass, FeSi75 roughly a quarter.

Buyers should read a grade number as the starting point of a specification, then confirm the four numbers that decide behaviour in the furnace: Si, Al, P and the reported size fraction. Two suppliers can both deliver "FeSi75" and still differ enough in aluminium and phosphorus to change nozzle behaviour in continuous casting.

Chemical Composition and Physical Properties

Parameter Ferro Silicon 45 Ferro Silicon 75
Silicon content 40-47% 74-80%
Aluminium 0.1-0.3% max 1.5%
Phosphorus max 0.04% max 0.035%
Iron balance balance
Bulk density about 3.3 g/cm3 about 2.8 g/cm3
Usual supply size 10-50 mm lumps 3-10 mm granules or 10-50 mm lumps
Main duty Inoculation, reduction Deoxidation, alloying, Mg reduction

The density gap follows directly from the lower atomic mass of silicon relative to iron, and it shows up in practice: a fixed volume of charging bucket carries less silicon when it is loaded with FeSi45. Lumps of FeSi45 dissolve more slowly in a ladle, which is often an advantage when a controlled, gradual silicon pickup is wanted.

Behaviour in Steelmaking and Foundry Practice

FeSi75 is a deoxidiser as well as an alloying addition. Added to a tapping ladle or to an electric arc furnace, it removes dissolved oxygen and delivers silicon to the heat at the same time. Its limited aluminium content matters in aluminium-killed, continuously cast steel, where excess aluminium can build up Al2O3 deposits at the submerged entry nozzle and shorten casting sequences. In magnesium production by the silicothermic Pidgeon route, FeSi75 is the reductant that converts magnesium oxide at roughly 1,200 degrees C; FeSi45 does not carry enough silicon per unit mass to drive that reaction economically.

FeSi45 is the classic foundry addition. Used as an inoculant in grey iron, it raises the number of active nucleation sites, promotes type A graphite and reduces chill depth at the edges of thin sections. It is also consumed as a reductant in ferromanganese and other silicothermic reductions where the higher iron content is not a penalty.

Size Fractions, Packaging and Storage

Size control is a specification item, not a logistics detail. FeSi45 is commonly supplied as 10-50 mm lumps; FeSi75 is often screened to 3-10 mm granules for fast solution in the ladle, with 10-50 mm or 0-3 mm fines available for other routes. Over-size pieces slow vanadium-style recovery in any tap-to-ladle addition, and an excessive fines fraction travels into the slag instead of the metal. Standard export packing is 25 kg moisture-barrier bags inside 1 MT jumbo bags, with steel drum options for smaller lots.

Ferrosilicon stored in damp conditions can generate hydrogen phosphide and hydrogen arsenide from residual moisture and impurities, so dry, ventilated warehousing with pallets off the floor is normal mill practice.

How to Choose Between the Two Grades

Work backwards from the process. If the target is a foundry inoculant dose or a silicothermic reduction where iron dilution is acceptable, FeSi45 gives the lowest cost per unit of delivered effect. If the target is steel deoxidation, electrical steel alloying or magnesium reduction, FeSi75 is the working grade because it delivers more silicon per tonne charged and keeps aluminium within the level that casting practice tolerates. Where both grades can technically work, compare on delivered silicon per tonne rather than price per tonne of alloy.

Documentation and Verification

Each heat should ship with a certificate of analysis that states the sampled lot, the analytical method and the measured values for Si, Al, C, S and P. X-ray fluorescence is the usual screening method, supported by combustion analysis for carbon and sulphur. Size verification is normally reported as a sieve analysis with the proportion of fines under the lower cut-off and any oversize fraction. Retained samples held for a defined period make later disputes resolvable without retesting the whole lot.

Frequently Asked Questions

Q: Is FeSi75 always more expensive to use than FeSi45?
A: No. FeSi75 carries roughly 1.6 times the silicon per tonne, so the correct comparison is cost per tonne of silicon delivered to the heat, not cost per tonne of alloy.

Q: Can FeSi45 replace FeSi75 in magnesium reduction?
A: It cannot do so economically. The silicothermic reduction of magnesium oxide needs the high silicon level and reaction energy that only the 75% grade supplies at a practical charge weight.

Q: Why does aluminium matter in FeSi75 for continuous casting?
A: Aluminium carried in with the alloy contributes to alumina build-up at the casting nozzle, so grades with a tight Al cap are preferred for aluminium-killed steel.

Q: Which size fraction dissolves fastest in a steel ladle?
A: Smaller screened fractions such as 3-10 mm dissolve fastest because of the larger specific surface area; large lumps need longer contact time and good bath stirring.

Q: How should ferrosilicon be stored before charging?
A: Keep it dry and ventilated, off the floor, away from standing water; moisture contact can release phosphine and arsine and also causes fines to cake.

Q: What does the certificate of analysis need to show?
A: Lot identity, sampling basis, analytical method and measured Si, Al, C, S and P values, plus the sieve analysis that documents the delivered size fraction.

Send Inquiry

Home

Phone

E-mail

Inquiry