What Defines a Low Cement Refractory Castable
A low cement refractory castable carries a calcium aluminate cement content typically between 1% and 3% by weight, balanced by reactive alumina, fine fillers and dispersant systems that keep the mix workable at low water addition. Conventional castables may contain 15-20% cement; cutting the cement reduces the lime available to form low-melting glassy phases, which raises refractoriness, hot strength and volume stability. The family divides into high alumina, mullite and corundum grades according to the aggregate system.
All three grades share the same placement methods, so one lining can use several grades with each chosen for the local wear condition rather than for a change in workmanship.
Grade Range and Specifications
| Item | High alumina YH-16 | Mullite YH-16K | Corundum YH-17 |
|---|---|---|---|
| Al2O3 content (%) | 65 | 70 | 85 |
| Bulk density after 110 C x 24 h (g/cm3) | 2.5 | 2.6 | 2.8 |
| Modulus of rupture, 110 C x 24 h (MPa) | 10 | 11 | 12 |
| Modulus of rupture, 1110 C x 3 h (MPa) | 12 | 13 | 14 |
| Cold crushing strength, 110 C x 24 h (MPa) | 80 | 90 | 100 |
| Cold crushing strength, 1110 C x 3 h (MPa) | 90 | 90 | 100 |
| Linear dimensional change, 1110 C x 3 h (%) | plus or minus 0.5 | plus or minus 0.5 | plus or minus 0.5 |
Values are quoted after drying at 110 C for 24 h and after firing at 1110 C for 3 h. Cold crushing strength and modulus of rupture follow ASTM C133, and alumina-silica castables are classified under ASTM C401. Water addition during mixing is normally held at 4.5-6% of dry weight; adding water beyond the recommended range lowers density and strength without improving placement.
Mullite and Corundum Chemistry in Service
Mullite, 3Al2O3.2SiO2, gives a balanced combination of hot strength, creep resistance and thermal shock tolerance, which makes it a common choice for cement kiln hoods, tertiary air ducts and cooler zones that cycle between roughly 1000 C and 1400 C. Corundum grades built on tabular or white fused alumina at about 85% Al2O3 push refractoriness above 1700 C and resist abrasion from clinker dust and slag, so they are used at the front kiln eye, in coal burner nozzles and in high-wear impact areas.
High alumina grades near 65% Al2O3 remain the general-purpose option for rear kiln sections, ductwork and steel plant repairs where abrasion is moderate and thermal cycling is frequent. Because the lime content is low in every grade, the bond phase stays refractory to high temperature and the lining holds its dimensions through repeated firing.
Placement, Curing and Dry-Out
Mix with clean water at the specified ratio and mix long enough to break down agglomerates; low cement mixes are sensitive to both water content and mixing energy.
Place by casting with vibration, or by gunning for repair work, and compact the mix fully around anchors and in corners.
Add a small percentage of organic fibre in thick sections so steam can escape during dry-out.
Cure in a moist environment before heating, then follow a controlled dry-out curve with holds at about 150 C, 350 C and 600 C.
Keep heating rates low above 600 C to protect the ceramic bond and prevent explosive spalling.
Applications
Steel furnaces, ladle and tundish working and safety linings
Ironmaking furnaces, hot blast stoves and trough linings
Glass kiln superstructure and regenerator chambers
Ceramic tunnel kiln car tops and burner zones
Cement kiln rear entrance, kiln hood, cooler and tertiary duct
Frequently Asked Questions
Q: What does low cement mean in practice?
It means a calcium aluminate cement content of about 1-3% by weight instead of the 15-20% used in conventional castables. The lower CaO input limits the glassy phase that forms at temperature, which is why low cement grades keep more of their strength and refractoriness in service.
Q: How much water should be added at the mixer?
Normally 4.5-6% of dry weight. Water should be measured by weight rather than judged by eye, because every extra point of water reduces bulk density and cold crushing strength and increases shrinkage on first firing.
Q: Why are properties reported after 110 C and 1110 C?
The two conditions separate the as-dried state from the fired state. Drying at 110 C for 24 h shows the hydraulic bond strength, while firing at 1110 C for 3 h shows what the lining does after the bond has converted to a ceramic one. Both numbers matter when comparing grades.
Q: What is the difference between mullite and corundum castables?
Mullite grades at about 70% Al2O3 balance thermal shock resistance with moderate abrasion resistance, while corundum grades at about 85% Al2O3 give the highest refractoriness and wear resistance at a higher material cost.
Q: Can low cement castables be gunned instead of cast?
Yes. Gunning mixes with the same chemistry are used for repairs and for areas where formwork is impractical, but water control at the nozzle is tighter than in casting because the operator cannot adjust the mix after placement.
Q: Where is the high alumina grade usually applied?
Around the rear entrance of the cement kiln, the kiln hood and the rear end of the cooler, where temperatures are moderate but thermal cycling and moderate abrasion are continuous.








