What the 65 Grade Tells You
Ferrosilicon is designated by its silicon content, so 65 ferrosilicon, often written FeSi65, contains roughly 65% silicon with the balance largely iron and small amounts of aluminium, calcium and carbon. The Chinese standard GB/T 2272 groups ferrosilicon into grades such as FeSi75, FeSi72, FeSi65 and FeSi45, each with its own limits on silicon and on the accompanying elements. Because the 65 grade is smelted at a lower temperature than the 75 grade, the furnace behaves differently: the burden is less fluid, less carbon is burned away, and the alloy is more sensitive to the quality of both the silica and the coke. Choosing a good 65 ferrosilicon therefore starts one step upstream, with the raw materials charged to the furnace.
Silica Quality: Purity and Particle Size
The silica, normally quartz or quartzite, is the source of the silicon and it dominates the economics of the smelt. Two properties decide whether a given silica will deliver a clean 65 ferrosilicon.
The first is chemical purity. A good silica carries a high SiO2 content and low levels of Al2O3, Fe2O3 and CaO, because these oxides are reduced alongside the silica and report either to the alloy or to the slag. Alumina in particular raises the aluminium content of the ferrosilicon and thickens the slag, while iron oxide adds iron that is not wanted in a controlled grade.
The second is particle size and its uniformity. Lumps that are too small carry more adhering impurity per tonne and pack the charge so tightly that furnace gas cannot pass through it; poor permeability traps heat, slows the descent of the burden and delays the reduction reaction. Lumps that are too large, or a charge with a very wide size spread, separate into layers as they descend, so part of the burden melts faster than the rest and the reduction becomes uneven. The practical target is a narrow, uniform size range matched to the furnace and to the electrode spacing.
| Property | Why it matters | What to look for |
|---|---|---|
| SiO2 content | Drives the silicon yield of the charge | Consistently high, verified lot by lot |
| Al2O3, Fe2O3, CaO | Report into the alloy and the slag | As low as the deposit allows |
| Lump size uniformity | Controls gas permeability of the burden | Narrow range with minimal fines |
| Surface cleanliness | Soil and fines add dead load | Screened or washed material |
Coke Quality: Ash and Moisture
Coke is the reductant and the second pillar of 65 ferrosilicon quality. A suitable coke has a high fixed carbon content together with low ash and low, stable moisture.
Ash is the mineral residue left behind when carbon burns, and it is the most damaging impurity in the reductant. A coke with high ash brings extra alumina and silica-bearing slag into the charge, and that slag softens and sinters inside the burden. Once the burden sinters it loses permeability, the furnace condition becomes unstable, and both silicon recovery and unit power consumption suffer. Low ash coke keeps the slag volume down and the burden open.
Moisture behaves differently but is just as disruptive. Water consumes heat when it evaporates and it changes the effective carbon-to-silica ratio from one charge to the next. A coke whose moisture swings widely makes the furnace condition fluctuate and the alloy analysis drift, which is particularly unwelcome when a customer is buying a defined 65 grade. Moisture should be reported delivery by delivery and the charge corrected for it.
Fixed carbon content is the figure that converts the stoichiometric carbon demand into an actual coke weight, so a low fixed carbon figure simply means more tonnes of coke per tonne of alloy. Sulphur and phosphorus should also be low, because both report almost entirely to the metal.
Selection Checklist for 65 Ferrosilicon
Confirm the silicon content and the impurity limits against a declared grade of GB/T 2272 rather than accepting a trade name alone.
Ask for the certificate of analysis for the actual heat, and check silicon, aluminium, calcium and carbon.
Inspect the silica for uniform lump size, minimal fines and a clean surface.
Check coke fixed carbon, ash, moisture, sulphur and phosphorus before the charge is fixed.
Compare the furnace response across suppliers; recovery, unit power consumption and slag volume reveal more than a single analysis.
Agree rejection limits in advance so an off-grade delivery can be handled without argument.
Frequently Asked Questions
Q: What does the 65 in 65 ferrosilicon mean?
It is the silicon content of the alloy, about 65% Si, with the balance made up mainly of iron and small amounts of aluminium, calcium and carbon.
Q: Why does silica particle size matter so much?
Because it sets the permeability of the burden. Fines pack the charge and block gas flow, while oversized or widely graded lumps stratify and melt unevenly, and either case slows the reduction of silica.
Q: Which coke property harms furnace condition most?
High ash is the worst offender because it sinters the burden and raises slag volume, while unstable moisture causes short-term swings in furnace condition and alloy analysis.
Q: Is the lower silicon grade easier to smelt?
It runs at a lower temperature with less carbon burnout, but the narrower operating window makes consistent raw material quality more important, not less.
Q: How can the grade actually received be verified?
By comparing the certificate of analysis for each heat against the declared GB/T 2272 limits and by checking silicon, aluminium, calcium and carbon on an independent sample.








