Jul 06, 2023 Leave a message

Magnesia Carbon Bricks for Steel Ladles and Converters: High Thermal Stability

What Magnesia Carbon Bricks Are

Magnesia carbon bricks, usually written as MgO-C bricks, are shaped basic refractories produced from high-purity dead-burned or fused magnesia, flake graphite and an organic binder such as phenolic resin. Fine graphite lamellae are dispersed through the magnesia matrix, interrupting crack propagation and giving the brick its characteristic resistance to thermal shock. Because the carbon phase is poorly wetted by molten basic slag, these bricks perform well wherever high temperature, basic slag and repeated thermal cycling occur together.

Commercial grades normally carry 10% to 18% carbon balanced against 74% to 80% MgO. Higher carbon levels favour thermal shock resistance and slag resistance; lower carbon levels provide higher thermal conductivity, better oxidation resistance and cleaner steel. Grade selection therefore follows the vessel, the steel grade and the campaign target rather than a single ideal composition.

Key Performance Advantages

High thermal stability: the graphite network accommodates rapid heating and cooling without macroscopic cracking or spalling, so the lining keeps its geometry through many heat cycles.

Slag corrosion resistance: the non-wetting carbon phase limits slag penetration, while the magnesia matrix neutralises both acidic and basic slags at the hot face.

Spalling resistance: a low elastic modulus combined with high thermal conductivity reduces the thermal gradient across the brick, which is the main driver of structural spalling.

Dimensional stability under load: refined grain sizing and resin bonding keep deformation low at steelmaking temperatures.

Controlled oxidation resistance: metallic antioxidants such as aluminium, silicon or magnesium are added in measured amounts to protect the carbon phase and densify the hot face.

Typical Technical Specifications

Property Typical range Test method
MgO content 74% – 80% GB/T 5069
Carbon content 10% – 18% GB/T 16555
Bulk density 2.85 – 3.00 g/cm³ GB/T 2997
Apparent porosity not more than 5% GB/T 2997
Cold crushing strength not less than 35 MPa GB/T 5072
Refractoriness under load (T0.6) not less than 1600 °C GB/T 5989
Typical service temperature up to 1700 °C in reducing conditions service experience

The figures above describe the normal working window for converter and ladle grades. A specific brick is engineered from the real vessel geometry, slag chemistry and campaign target, so a certificate of analysis for MgO, carbon, porosity and strength should always be requested for the delivered lot.

Applications in Steelmaking and Non-Ferrous Metallurgy

MgO-C bricks dominate the wear-critical zones of modern steel plants because those zones combine high temperature with aggressive slag and rapid cycling. Typical positions include:

Converter slag lines, hot spots and trunnion areas

Electric arc furnace slag lines and hot spots

Steel ladle slag line and freeboard linings

Vacuum degassing and secondary metallurgy vessels

Torpedo ladles and hot metal transfer cars

Holding and refining furnaces for copper, nickel and other non-ferrous melts

In non-ferrous service the same combination of properties is used, but slag chemistry differs sharply from steel practice, so brick grade and antioxidant package are normally adjusted to the specific furnace.

Storage, Installation and Lining Practice

Magnesia is sensitive to moisture, and a resin-bonded brick loses strength if it hydrates. Bricks should be stored under cover on dry pallets, kept in their original packing until installation, and used within the shelf life declared by the producer. During lining work the following points protect performance:

Clean the shell and check it for ovality before laying the first course.

Use the specified mortar or dry-joint system and keep joint thickness within the lining design.

Keep an expansion allowance at the ends of each ring to prevent compressive overload during heat-up.

Follow the drying and preheating curve, especially the low-temperature segment where binder volatiles are released.

Inspect the hot face after each campaign and record wear profiles so that the next lining can be adjusted.

Frequently Asked Questions

Q: How do I choose between a 10% carbon and an 18% carbon grade?
Low-carbon grades are preferred where thermal conductivity, oxidation resistance and steel cleanliness matter most, for example in some ladle and degassing positions. High-carbon grades are chosen for slag lines and hot spots that see extreme thermal cycling, because extra graphite improves both spalling resistance and slag non-wetting behaviour.

Q: Are fused and sintered magnesia interchangeable?
Not freely. Fused magnesia has larger crystals, lower porosity and higher purity, which improves slag resistance and hot strength, while sintered magnesia is more economical. The correct choice depends on the wear mechanism dominating the selected zone.

Q: Can magnesia carbon bricks be used in cement kilns?
They are designed for basic slag and reducing service. In cement kilns the atmosphere is strongly oxidising, so carbon would burn out quickly and a different basic brick or a magnesia-spinel grade is normally the better answer.

Q: How should the bricks be stored before installation?
Keep them dry, under cover, on pallets and in the original packaging. Do not expose them to rain, standing water or long periods of high humidity, because hydration of magnesia reduces strength and can cause cracking during heat-up.

Q: Is preheating necessary before the vessel enters service?
Yes. A controlled dry-out and preheating schedule removes moisture and volatiles from the binder and builds a dense, protective hot face. Skipping or shortening the low-temperature hold is one of the most common causes of early lining damage.

Q: How is oxidation of the carbon phase controlled?
Three measures work together: metallic antioxidants in the brick body, a dense and well-fired hot face, and operating practice that avoids prolonged exposure to strongly oxidising atmospheres or excessive downtime at temperature with air ingress.

Send Inquiry

Home

Phone

E-mail

Inquiry