What Magnesia Carbon Bricks Are and Why They Are Versatile
Magnesia carbon brick is a basic refractory made from dead-burned or fused magnesia, graphite, a carbonaceous binder such as phenolic resin, and small additions of metallic antioxidants. The carbon phase gives the brick outstanding thermal shock resistance and a low wettability by molten steel and slag, while the magnesia matrix supplies refractoriness and resistance to basic slags and fluxes. That combination of properties is the reason one material family serves duties that are otherwise very different, from converter slag lines to non-ferrous melting vessels and cement kiln burning zones.
The product standard for magnesia carbon bricks is GB/T 22589, supported by GB/T 2997 for apparent porosity and bulk density, GB/T 5072 for cold crushing strength and ISO 10081-4 for the classification of dense shaped special products. Dimensional tolerance and residual carbon content are agreed against the drawing and the application.
Composition and Typical Properties
Property balance is set by three variables: magnesia quality and purity, carbon level, and antioxidant addition. Higher carbon content improves thermal shock resistance and reduces sticking to metal, but it also lowers density and increases susceptibility to oxidation at the surface. Higher magnesia content improves corrosion resistance to basic slags.
| Property | Typical range | Effect on service performance |
|---|---|---|
| MgO content (%) | 70-85 | Higher values improve resistance to basic slags and reduce wear at the hot face |
| Carbon content (%) | 8-20 | Higher values improve thermal shock resistance and reduce slag wetting |
| Apparent porosity (%) | 3-8 | Lower porosity slows slag penetration and oxidation of the carbon bond |
| Bulk density (g/cm3) | 2.85-3.05 | Higher density supports better erosion resistance in high flow zones |
| Cold crushing strength (MPa) | 30-55 | Confirms the strength of the resin bond before service |
| Hot modulus of rupture at 1400 °C (MPa) | 5-12 | Measures the load-bearing capacity of the bond at working temperature |
Antioxidants such as aluminium, magnesium and silicon powders protect the carbon from oxidation between roughly 800 °C and 1400 °C, the range in which carbon would otherwise be burned away by oxygen carried in the slag or in the furnace atmosphere. The type and level of addition are matched to the duty: silicon and aluminium additions are common in converter and ladle bricks, while magnesium-rich additions are used where the slag is highly basic.
Applications Across Industries
Basic oxygen steelmaking: converter linings and slag lines, where the brick must resist high temperature, basic slag and heavy thermal cycling between heats.
Electric arc furnaces: hot spots, slag lines and the area above the slag, where intense radiation and rapid power changes place a premium on thermal shock resistance.
Secondary metallurgy: ladle slag lines, ladle bottoms and degassing vessels, where low carbon grades are used to avoid carbon pickup in low carbon steel grades.
Non-ferrous metallurgy: copper and nickel converters and melting vessels, where magnesia carbon bricks resist basic slags and metal wash.
Cement and lime production: burning zone linings and transition zones where basic refractories are required and alkali attack must be limited.
Other high temperature plant: incinerators and gasification vessels with basic slag chemistry, where a basic brick is needed and thermal cycling is frequent.
Low carbon grades, typically with carbon contents at the lower end of the range, are used where the steel specification limits carbon pickup, while high carbon grades suit slag line duties where thermal shock controls life. Grade selection is therefore always a compromise between corrosion resistance, thermal shock resistance and contamination limits.
Selection, Handling and Service Guidance
Because the resin bond and the carbon phase are sensitive to moisture and oxidation, handling practice has a direct effect on performance:
Store bricks under cover and keep them dry; resin-bonded bricks that absorb moisture lose strength and can steam during heat-up.
Use the correct side of the brick against the hot face and keep joints thin and tightly closed, so that slag cannot penetrate between bricks.
Fit stainless steel plates or foil where the design requires them, to reduce joint oxidation and metal penetration.
Allow for expansion in the design; magnesia carbon bricks expand on first heating as the bond cures, and the lining needs room to accommodate it.
Control the heat-up curve of a newly lined vessel so that the resin bond cures gradually and the joints close before the vessel goes into production service.
In service, wear is normally a combination of slag corrosion along the hot face, oxidation of the carbon bond at joints and cracks, and mechanical erosion in high flow areas. Keeping the hot face cool through good backup insulation, avoiding excessive oxygen lancing and maintaining a stable slag chemistry all extend campaign life. Inspections during relines should record wear profiles zone by zone, because the data show which areas justify a higher grade brick in the next campaign.
Frequently Asked Questions
Q: What is the difference between magnesia carbon brick and magnesia brick?
Magnesia brick is bonded by ceramic sintering and contains little or no carbon, so it has good slag resistance but limited thermal shock resistance. Magnesia carbon brick uses a resin bond and a graphite phase, which improves thermal shock resistance and reduces wetting by molten slag and steel.
Q: How is the carbon content chosen for a given application?
Higher carbon contents are chosen where thermal cycling is severe and where some carbon pickup is acceptable. Lower carbon contents are chosen for slag lines with aggressive basic slags and for vessels producing low carbon steels, where carbon transfer must be limited.
Q: Why do antioxidants matter in magnesia carbon bricks?
Antioxidants react preferentially with oxygen and form protective phases that fill pores near the hot face, so the carbon bond is not burned away. This preserves the strength and slag resistance of the brick between roughly 800 °C and 1400 °C.
Q: Can magnesia carbon bricks be stored outdoors?
They should be kept dry and under cover. Prolonged exposure to rain or ground moisture weakens the resin bond and can cause surface damage and steam spalling during the first heat-up.
Q: How should a magnesia carbon lining be commissioned?
Commission with a controlled heat-up curve, holding at intermediate temperatures so that the resin bond cures and any residual moisture escapes, and bring the vessel to working temperature gradually before the first production heat. This protects both the brick and the joints.
Q: What causes the lining to wear fastest at the slag line?
The slag line combines high temperature, slag movement and chemical attack, and the carbon bond is the first component to be oxidised. Denser bricks with a matched antioxidant addition and cooler operating practice reduce the wear rate at this zone.








