What Ferro Silicon 75 Means
Ferro silicon 75, usually written FeSi75, is a ferrosilicon grade in which the silicon content is held in the 74-80% band. It is the most widely traded ferrosilicon grade in China and is produced in submerged-arc electric furnaces from quartz, carbon reductants and an iron source. Compared with ferro silicon 72, FeSi75 delivers a higher silicon yield per tonne of alloy charged, which reduces the weight of alloy a melt shop has to handle for a given silicon addition and lowers the volume of slag-forming carrier material.
The grade is used for deoxidation of steel, for silicon alloying in electrical and spring steels, and as an inoculant in grey and ductile iron foundries. It is supplied as lump, granules and powder, so the same grade can serve furnace charging, wire feeding and welding consumable production.
FeSi75 Grade Specifications
The three common sub-grades differ mainly in the ceilings applied to manganese, chromium and carbon. Silicon content is the same band for each of them.
| Grade | Si (%) | Mn (%) max | Cr (%) max | P (%) max | S (%) max | C (%) max |
|---|---|---|---|---|---|---|
| FeSi75-A | 74.0-80.0 | 0.40 | 0.30 | 0.04 | 0.02 | 0.10 |
| FeSi75-B | 74.0-80.0 | 0.40 | 0.30 | 0.04 | 0.02 | 0.10 |
| FeSi75-C | 72.0-80.0 | 0.50 | 0.50 | 0.04 | 0.02 | 0.20 |
Aluminium and calcium are normally left to the agreed specification rather than fixed by the grade name, and tighter windows can be negotiated when a heat is destined for electrical steel or for filler wire production. Buyers should always treat the certificate of analysis as the governing document, not the grade label alone.
Available Sizes and Packing
Lump - 10-50 mm and 10-100 mm for furnace and ladle charging.
Granules - 0-1 mm, 0-3 mm, 0-10 mm and 1-10 mm for wire feeding, briquetting and additions where a controlled dissolution rate matters.
Powder - milled and screened to mesh specifications for welding consumables and dense-medium applications.
Packing - 25 kg PP or paper bags, 1 MT jumbo bags, or steel drums for fine grades; private-label marking is straightforward for export orders.
Size and packing can be produced to the customer's requirement, but each non-standard combination carries a minimum order quantity because screening and packing lines are set up per campaign.
How Ferrosilicon 75 Is Produced
Quartz is the silicon source, coke and coal are the reductants, and steel scrap or iron chips supply the iron balance. The charge is fed to a submerged-arc electric furnace where the electrodes are buried in the burden and reduction takes place at high temperature; the molten alloy is tapped at intervals, cast into beds, cooled, crushed and screened into the delivery sizes.
Three production facts explain most commercial behaviour in this grade:
Electricity dominates cost. Ferrosilicon smelting is highly power-intensive, so Chinese production is concentrated in regions with competitive and stable electricity, and smelter load following affects spot availability more than ore prices do.
Silicon recovery is the yield lever. Dust carry-over, reductant quality and charge balance decide how much silicon leaves the furnace as product rather than as fume, which is why process control discipline separates a stable supplier from a volatile one.
Screening decides the deliverable. Crushing a tapped ingot produces a distribution, not a single size, so the plant's screening capacity and its ability to place by-product fines determine lead time for any given size fraction.
Quality Control and Buyer Checklist
Ferrosilicon is a commodity where two suppliers can quote the same grade and still deliver materially different behaviour in the ladle, because silicon content, impurity levels and size distribution all shift recovery. A practical check on every lot covers:
Certificate of analysis for Si, Mn, Cr, P, S and C, with the test method identified.
Screening report for the actual size fraction delivered, not the nominal range ordered.
Moisture-free packing: waterproof bags inside jumbo bags, with no evidence of water ingress on arrival.
Sampling and lot traceability, so a non-conformance can be traced back to one campaign.
Third-party pre-shipment inspection where the contract requires independent verification of weight and chemistry.
A supplier's willingness to hold a sample of each lot and to repeat the analysis on request is a more useful signal of process control than any single test result.
FAQ
Q: What is the difference between FeSi75-A, FeSi75-B and FeSi75-C?
The grades differ in impurity ceilings. Grade A and grade B apply manganese 0.40%, chromium 0.30% and carbon 0.10% maxima, while grade C allows manganese 0.50%, chromium 0.50% and carbon 0.20%, with a wider silicon band that starts at 72.0%.
Q: Is ferro silicon 75 or ferro silicon 72 better for steel deoxidation?
Both work. FeSi75 adds more silicon per tonne of alloy, so it reduces handling volume and carrier material, while FeSi72 is often cheaper per unit of silicon. The choice usually comes down to the plant's addition practice and the price spread at the time of purchase.
Q: What silicon content should the certificate of analysis show?
For FeSi75-A and FeSi75-B the silicon content should fall in the 74.0-80.0% band, and for FeSi75-C in the 72.0-80.0% band. A result outside the band should be treated as a non-conformance regardless of the grade label.
Q: Can ferrosilicon 75 be supplied in a specific size?
Yes. Sizes such as 0-1 mm, 0-3 mm, 0-10 mm, 1-10 mm, 10-50 mm and 10-100 mm are standard offerings, and other fractions can be screened to order against a minimum quantity.
Q: How many years of production experience matters to a buyer?
Long service history is only useful if it comes with traceable process discipline. Ask for the lot records, the analysis method and the corrective action history behind any past non-conformance rather than relying on years in business as a proxy for quality.
Q: How should ferrosilicon 75 be stored on site?
Keep it in a dry, covered store on pallets with bags sealed until use. Damp fines release phosphine and hydrogen, so enclosed handling areas need ventilation and gas monitoring before entry.








