What Ceramic Fibres Are
Ordinary ceramic fibre is also known as aluminium silicate fibre. It is called a ceramic fibre because one of its main components is aluminium oxide, the same oxide that forms the basis of porcelain. The fibre is made by melting an alumina-silica raw material and then converting the melt into fine filaments, which are collected, needled or felted and cut into the product forms used in industry.
Ceramic fibre products are industrial articles manufactured from ceramic fibre as the raw material. They are light in weight, resist high temperature, show good thermal stability, have low thermal conductivity and low specific heat, and tolerate mechanical vibration. These characteristics make them suitable for high-temperature, high-pressure and abrasive service environments.
Composition and Classification Temperature
Standard alumina-silica fibre contains alumina and silica in roughly comparable proportions, with alumina generally in the range of about 45 to 55 percent and silica making up the balance. Because the alumina content governs the refractoriness of the fibre, additions are used to raise the working limit:
Zirconia additions produce the zirconia-containing grades, which are used where a higher classification temperature is required.
Chromium oxide additions further increase the usable temperature and help to slow down the devitrification that eventually embrittles the fibre.
In China there are more than two hundred ceramic fibre manufacturers of different sizes, but for fibres with a classification temperature of 1425 degrees Celsius and below (including the zirconia-containing fibres) the production processes fall into only two categories: the spun route, which yields silk spinning blankets, and the blown route, which yields jet blown blankets. Blankets from the two routes differ in fibre diameter, shot content and tensile strength, so they behave differently in service.
Product Forms and Key Properties
| Property | Behaviour of ceramic fibre products |
|---|---|
| Density | Very low compared with dense refractory brick, which cuts structural load and heat storage |
| Thermal conductivity | Low, because the fibre structure traps still air between filaments |
| Heat capacity | Low specific heat, so furnaces heat up and cool down quickly |
| Temperature resistance | High, with the usable limit set by the classification temperature of the grade |
| Thermal stability | Good resistance to thermal shock and cycling |
| Mechanical vibration | Withstands vibration better than brittle dense refractories |
| Chemistry | Non-toxic as supplied; dust control and respiratory protection are still required during installation or removal |
Ceramic fibre is supplied as blanket, board, paper, felt, bulk fibre, rope, yarn and vacuum-formed shapes. Blanket and board are the most common forms in furnace and kiln construction, while paper and shapes are used for seals, gaskets and expansion joints.
Why Ceramic Fibre Is Used as a Refractory Material
Dense refractories insulate by mass. Ceramic fibre insulates by structure: billions of fine filaments create a labyrinth of still air that blocks heat flow while adding almost no weight. The practical consequences are thinner linings, lighter steelwork, faster furnace cycling, lower heat storage losses and easier maintenance, which is why fibre linings replaced brick and castable linings in many reheat, annealing, ceramic and petrochemical applications.
Typical Applications
Linings and back-up insulation for industrial furnaces, kilns, ladles and boilers.
Expansion joints, door seals, gaskets and flexible connectors that must survive thermal movement.
High-temperature filtration and thermal barriers in process equipment.
Automotive and emission-control insulation, and fire protection of steel structures and ducts.
Heat shields and insulation in foundries and in the aluminium, glass and ceramics industries.
Selection and Specification Notes
Selection should start from the classification temperature of the grade, then from the atmosphere, the chemical environment and the mechanical loads the lining will see. Blanket thickness and density are set by the required cold face temperature. Products are commonly specified against recognised refractory ceramic fibre specifications, such as ASTM C892 for high-temperature fibre blanket thermal insulation and the corresponding national product standards for refractory ceramic fibre products, so that classification temperature, density and shot content are compared on the same basis. Above the classification temperature the fibre begins to sinter and shrink; that shrinkage, not melting, sets the real service limit.
FAQ
Q: Why are aluminium silicate fibres called ceramic fibres?
Because one of their principal components is aluminium oxide, which is the main constituent of porcelain. The name describes the oxide chemistry rather than the manufacturing route.
Q: What effect do zirconia and chromium oxide have?
Both additions raise the temperature at which the fibre can be used. Zirconia produces the zirconia-containing grades, and chromium oxide is used to extend service temperature and to retard devitrification.
Q: What is the difference between a spun blanket and a blown blanket?
Spun (silk spinning) blankets are made by spinning the melt into filaments, and blown (jet blown) blankets by jetting the melt with air or steam. The two routes give different fibre diameter, shot content and strength, which affects handling and service life.
Q: What advantages do ceramic fibre products offer over dense refractories?
Lower weight, lower thermal conductivity, low heat capacity and good thermal stability, so thinner linings are possible and furnaces cycle faster with less stored heat.
Q: Are ceramic fibre products safe to handle?
The products are non-toxic as supplied, but they release dust when cut or removed. Dust control, suitable clothing and respiratory protection should be used during installation, demolition and maintenance.
Q: Does the classification temperature equal the working temperature?
No. The classification temperature is a ranking value. Continuous service is normally set below it, with allowance for shrinkage, atmosphere and mechanical loading.








